Chlorinated Rubber Paint and Primer

“SP-PRERUBBER ZC 33” is an Air Drying Single pack Zinc Chromate Pigmented Chlorinated Rubber Based Primer suitably for mild or moderate environments. It Gives Superior corrosion resistant property, Matt, Tough, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance and Good Flexibility. It also helps in increasing the covering of final coat and acts as grip to final finish coat thus ensures better adhesion. Specially designed for saline environments and industrial environments.

Features :

• A durable Matt Finish Coat
• Superior anti-rust property.
• Excellent hardness with color retention property.
• Tough, Durable, fast drying primer.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion

“SP-PRERUBBER ZC 33” is an Air Drying Single pack Zinc Chromate Pigmented Chlorinated Rubber Based Primer suitably for mild or moderate environments. It Gives Superior corrosion resistant property, Matt, Tough, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance and Good Flexibility. It also helps in increasing the covering of final coat and acts as grip to final finish coat thus ensures better adhesion. Specially designed for saline environments and industrial environments.


 

Features :

• A durable Matt Finish Coat
• Superior anti-rust property.
• Excellent hardness with color retention property.
• Tough, Durable, fast drying primer.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion
• Good opacity and better hiding power.
• Can be applied on mild steel, other metallic surfaces.


Area of Application :

• Machinery equipments.
• Specially Designed for Saline Environments
• Structures
• Containers
• Cabins
• Scaffolding pipes
• Pipeline
• Metal furniture
• Collapsible gates, grills, gates, etc.


Direction For Use :

Surface Preparation :
Surface to be painted should be dry and free from oil, grease, dust, rust and other contaminants. This can be done by wire brush, Emery Paper, Scrapping Tools.

Priming :
Apply 1 to 2 Coats of SP-PRERUBBER ZC 33 On Surface as per requirement after surface preparation with Interval of overnight. Sand the Surface and wipe it clean.

Top Coat Application :
Then Apply top coat with interval of overnight. Apply minimum 2 Coats on surface. Use of chlorinated rubber based paints is recommended.

Application Method :

• By airless spray-Tip size : 0.015-0.017 inches
• Pressure : 150 kg/ sq. cm (2100 P.S.I)
• Conventional air spray : can also be used
• Roller or brush:can also be used. However, additional coats may be required to be applied to get desired DFT. This method of application is suitable at weld-seams, edges, corners, rivets, Stripe coating etc.


Special instruction :

• Do not apply the paint if the temperature is less than 10 degree.
• Do not overthin the paint
• Stir well before use
• keep the container tightly closed and away from direct sunlight.
• In case of contact with use plenty of water and take medical advice if irritation persists.


Drying Time

• SD- Approx. 5 minutes at 30 Degree Centigrade
• HD- Approx. 1-2 Hours at 30 Degree Centigrade
• TF- Overnight

 

“SP-PRERUBBER ZC 33” is an Air Drying Single pack Zinc Phosphate Pigmented Chlorinated Rubber Based Primer suitably for mild or moderate environments. It Gives Superior corrosion resistant property, Matt, Tough, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance and Good Flexibility. It also helps in increasing the covering of final coat and acts as grip to final finish coat thus ensures better adhesion. Specially designed for saline environments and industrial environments.

Features :

• A durable Matt Finish Coat
• Superior anti-rust property.
• Excellent hardness with color retention property.
• Tough, Durable, fast drying primer.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion

“SP-PRERUBBER ZC 33” is an Air Drying Single pack Zinc Phosphate Pigmented Chlorinated Rubber Based Primer suitably for mild or moderate environments. It Gives Superior corrosion resistant property, Matt, Tough, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance and Good Flexibility. It also helps in increasing the covering of final coat and acts as grip to final finish coat thus ensures better adhesion. Specially designed for saline environments and industrial environments.


 

Features :

• A durable Matt Finish Coat
• Superior anti-rust property.
• Excellent hardness with color retention property.
• Tough, Durable, fast drying primer.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion
• Good opacity and better hiding power.
• Can be applied on mild steel, other metallic surfaces.


Area of Application :

• Machinery equipments.
• Specially Designed for Saline Environments
• Structures
• Containers
• Cabins
• Scaffolding pipes
• Pipeline
• Metal furniture
• Collapsible gates, grills, gates, etc.


Direction For Use :

Surface Preparation :
Surface to be painted should be dry and free from oil, grease, dust, rust and other contaminants. This can be done by wire brush, Emery Paper, Scrapping Tools.

Priming :
Apply 1 to 2 Coats of SP-PRERUBBER ZC 33 On Surface as per requirement after surface preparation with Interval of overnight. Sand the Surface and wipe it clean.

Top Coat Application :
Then Apply top coat with interval of overnight. Apply minimum 2 Coats on surface. Use of chlorinated rubber based paints is recommended.

Application Method :

• By airless spray-Tip size : 0.015-0.017 inches
• Pressure : 150 kg/ sq. cm (2100 P.S.I)
• Conventional air spray : can also be used
• Roller or brush : can also be used. However, additional coats may be required to be applied to get desired DFT. This method of application is suitable at weld-seams, edges, corners, rivets, Stripe coating etc.


Special instruction :

• Do not apply the paint if the temperature is less than 10 degree.
• Do not overthin the paint
• Stir well before use
• keep the container tightly closed and away from direct sunlight.
• In case of contact with use plenty of water and take medical advice if irritation persists.


Drying Time

• SD- Approx. 5 minutes at 30 Degree Centigrade
• HD- Approx. 1-2 Hours at 30 Degree Centigrade
• TF- Overnight

 

“SP-RUBBER COAT 33” is a single pack air drying chlorinated rubber based primer.  It Gives matt  finish, Tough, Rust Preventing Coating, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance, Excellent Flexibility. It is specially designed for saline environments. This product is also recommended to be used during monsoon season or cold temperature but not to be applied under running water. It provides grip to finish coat and helps in increasing covering of final coat.

Features :

• Quick drying property.
• Recommended for the use in industrial environments
• Suitable for exterior and interior use.
• Specially designed for saline environments
• Resistant to splash and mild chemicals.
• Excellent hardness and color retention property.
...

“SP-RUBBER COAT 33” is a single pack air drying chlorinated rubber based primer.  It Gives matt  finish, Tough, Rust Preventing Coating, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance, Excellent Flexibility. It is specially designed for saline environments. This product is also recommended to be used during monsoon season or cold temperature but not to be applied under running water. It provides grip to finish coat and helps in increasing covering of final coat.

Features :

• Quick drying property.
• Recommended for the use in industrial environments
• Suitable for exterior and interior use.
• Specially designed for saline environments
• Resistant to splash and mild chemicals.
• Excellent hardness and color retention property.
• Tough, Rust preventing coating.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion
• Good opacity and better hiding power.
• Can be applied on steel, walls and other metallic surfaces.

Area of Application :

• Machinery equipments
• Drum Enamels
• Cabins
• Containers
• Wood Furniture
• Pipeline
• Metal furniture
• Collapsible gates, grills, gates, etc.

Direction For Use :

Surface Preparation :
Surface to be painted should be dry and free from oil, grease, dust, rust and other contaminants. This can be done by wire brush, Emery Paper, Scrapping Tools.

Priming :
Apply 2 Coats of SP- RUBBER PRIMO 33 primer On Surface after surface preparation with Interval of overnight. Sand the Surface and wipe it clean.

Top Coat Application :
Apply top coat SP-RUBBER COAT 33 is recommended with interval of 6-8 hours. Apply minimum 2 Coats on surface.

Application Method :

• By airless spray- Tip size : 0.38-0.46 mm
• Pressure : 10-13 MPa (1400-1800 p.s.i)
• Conventional air spray : Tip size : 015-3.33 mm
• Pressure : 0.3-0.4 MPa ( 43-57 p.s.i)
• Roller or brush : can also be used. However, additional coats may be required to be applied to get desired DFT. This method of application is suitable at weld-seams, edges, corners, rivets, Stripe coating etc.

Special instruction :

• Do not apply the paint if the temperature is less than 10 degree.
• Do not overthin the paint
• Stir well before use
• Keep the container tightly closed and away from direct sunlight.
• In case of contact with use plenty of water and take medical advice if irritation persists.

Drying Time

• SD- Approx. 5 Minutes at 30 Degree Centigrade
• HD- Approx. 2 Hours at 30 Degree Centigrade
• TF- Overnight

“SP-RUBBER COAT 33” is a single pack air drying chlorinated rubber based finish paint.  It Gives Eggshell finish, Tough, Rust Preventing Coating, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance, Excellent Flexibility. It is specially designed for saline environments. This product is also recommended to be used during monsoon season or cold temperature but not to be applied under running water.

Features:

• Quick drying property.
• Recommended for the use in industrial environments.
• Suitable for exterior and interior use.
• Specially designed for saline environments
• Resistant to splash and mild chemicals.
• Excellent hardness and color retention property.
• A durable Eggshell Finish Coat.
• Tough, Rust preventing coating.

“SP-RUBBER COAT 33” is a single pack air drying chlorinated rubber based finish paint.  It Gives Eggshell finish, Tough, Rust Preventing Coating, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance, Excellent Flexibility. It is specially designed for saline environments. This product is also recommended to be used during monsoon season or cold temperature but not to be applied under running water.

 

Features:

 

• Quick drying property.
• Recommended for the use in industrial environments.
• Suitable for exterior and interior use.
• Specially designed for saline environments
• Resistant to splash and mild chemicals.
• Excellent hardness and color retention property.
• A durable Eggshell Finish Coat.
• Tough, Rust preventing coating.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion
• Good opacity and better hiding power.
• Can be applied  on steel, walls and other metallic surfaces.

 

Area of Application:



• Machinery equipments
• Drum Enamels
• Cabins
• Containers
• Wood Furniture
• Indoor walls
• Pipeline
• Metal furniture
• Collapsible gates, grills, gates, etc.

 

Direction For Use:

 

Surface Preparation:

Surface to be painted should be dry and free from oil, grease, dust, rust and other contaminants. This can be done by wire brush, Emery Paper, Scrapping Tools.


 

Priming

Apply 2 Coats of Primer On Surface after surface preparation with Interval of overnight. Sand the Surface and wipe it clean.  Use Chlorinated Rubber primer for this application. Other primer may also be used after consulting with us.


 

Top Coat Application

Apply top coat ‘SP-RUBBER COAT 33 “with interval of 6-8 hours. Apply minimum 2 Coats on surface.


 

Application Method:


 

• By airless spray:  Tip size: 0.38-0.46 mm
• Pressure: 10-13 MPa (1400-1800 p.s.i)
• Conventional air spray  Tip size : 015-3.33 mm
• Pressure: 0.3-0.4 MPa ( 43-57 p.s.i)

 

Roller or brush: can also be used. However, additional coats may be required to be applied to get desired DFT. This method of application is suitable at weld-seams, edges, corners, rivets, Stripe coating etc

 

Special Instruction:

 

• Do not apply the paint if the temperature is less than 10 degree.
• Do not overthin the paint
• Stir well before use
• keep the container  tightly closed and away from direct sunlight.
• In case of contact with use plenty of water and take medical advice if irritation persists.

 

 

“SP-RUBBER INT PRIMO 33” is a single pack air drying chlorinated rubber based intermediate primer cum finish paint . it comes in 2 color. Grey- titanium base & brown – mecacious iron oxide base.  It Gives matt  finish, Tough, Rust Preventing Coating, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance, Excellent Flexibility. It is specially designed for saline environments. This product is also recommended to be used during monsoon season or cold temperature but not to be applied under running water. It provides grip to finish coat and helps in increasing covering of final coat.

Features:

• Quick drying property.
• Recommended for the use in industrial environments.
• Suitable for exterior and interior use.
• Specially designed for saline environments
• R...

“SP-RUBBER INT PRIMO 33” is a single pack air drying chlorinated rubber based intermediate primer cum finish paint . it comes in 2 color. Grey- titanium base & brown – mecacious iron oxide base.  It Gives matt  finish, Tough, Rust Preventing Coating, Good Abrasion Resistance, Good Chemical Resistance, Good Impact Resistance, Excellent Flexibility. It is specially designed for saline environments. This product is also recommended to be used during monsoon season or cold temperature but not to be applied under running water. It provides grip to finish coat and helps in increasing covering of final coat.

Features:

• Quick drying property.
• Recommended for the use in industrial environments.
• Suitable for exterior and interior use.
• Specially designed for saline environments
• Resistant to splash and mild chemicals.
• Excellent hardness and color retention property.
• Tough, Rust preventing coating.
• Ease of application, can be applied by brush, roller or spray.
• Good resistance to impact and abrasion
• Good opacity and better hiding power.
• Can be applied  on steel, walls and other metallic surfaces.

Area of Application:

• Machinery equipments
• Drum Enamels
• Cabins
• Containers
• Wood Furniture
• Pipeline
• Metal furniture
• Collapsible gates, grills, gates, etc.

Direction For Use:

• Surface Preparation: Surface to be painted should be dry and free from oil, grease, dust, rust and other contaminants. This can be done by wire brush, Emery Paper,Scrapping Tools.
  

• Priming: Apply 2 Coats of “SP- RUBBER PRIMO 33” primer On Surface after surface preparation with Interval of overnight. Sand the Surface and wipe it clean.

• Intermediate coat

Top Coat Application :

Apply top coat ‘SP-RUBBER COAT 33 “ is recommended with interval of 6-8 hours. Apply minimum 2 Coats on surface.

Application Method

By airless spray

 Tip size: 0.38-0.46 mm

Pressure: 10-13 MPa (1400-1800 p.s.i)

Conventional air spray :

Tip size : 1.5-3.33 mm

Pressure: 0.3-0.4 MPa ( 43-57 p.s.i)

Roller or brush: can also be used. However, additional coats may be required to be applied to get desired DFT. This method of application is suitable at weld-seams, edges, corners, rivets, Stripe coating etc.

Special instruction:

• Do not apply the paint if the temperature is less than 10 degree.
• Do not overthin the paint
• Stir well before use
• keep the container  tightly closed and away from direct sunlight.
• In case of contact with use plenty of water and take medical advice if irritation persists.